Backmount Clips

So we built a d-ring to mount onto almost any backplate! How you ask? Well we made one of the holes fixed so your d-ring stays located in the same area and then we made a 2 1/4" long slot so no matter where you mount it and on any of the different made backplates you can secure the bottom hardware by sliding it to match up with another hole in your backplate!!

We also made this d-ring just a little larger then normal to make sure you can find it with ease on the side of your plate! Ir reaces out 1 5/8" inches measuring the inside of the D

We also supply all the needed 3/8"-16 stainless steel hardware and use a nylon insert lock nut to hold it tightly to your plate. Our kit includes:

1 Backplate D-Ring ** 304 marine grade stainless

2 7/32 Hex Head button cap screw **316SS

* You need a 7/32 Allen Head Tool for this bolt 

2 Nylon insert lock nut **316SS

4 Washers **316SS

Overall Measurements:

3 1/2" inches long

2 5/8" inches wide

1/4" thick

1 5/8" inside D measurement

Slot Measurement: Middle of fixed hole to shortest to furtherest slot length:  15/16" to 3" inches

Your backplate D-Ring has been tumbed for at least 48 hours giving it a smooth finish with no sarpe edges

If you want your D-ring slightly bent select from our drop down box below and make sure to read to know how the bend will be facing

* Example: If you select the fixed hole on the top and you want your D-ring slightly bent forward it means your bend is slightly in front of your backplate hardware and if bent backwards it would mean your bend is slightly behind where you mount it... 

This backmount you use with 2" inch webbing. Perfect to use on your crotch strap for hanging items on your backside with no issues

Side clip off section are both slightly angled so you can find it to clip off easily during your dive

Overall width is roughly 3 1/4" / 2 5/8" inches Long

Made from 304 stainless steel

This has been tumbled for 48 hours to have all the edges been smooth and prevents any webbing damage

You can select flat or slight bend on the sides

Made in the U.S.A.

This backmount you use with 2" inch webbing. Perfect to use on your crotch strap for hanging items on your backside with no issues

Our latest version now uses our slip on webbing type design!! 

Side clip off section are both slightly angled so you can find it to clip off easily during your dive

Overall width is roughly 3 1/4" / 2 5/8" inches Long

Made from 304 stainless steel

This has been tumbled for 48 hours to have all the edges been smooth and prevents any webbing damage

You can select flat or slight bend on the sides

Made in the U.S.A.

This backmount you use with 2" inch webbing. Our clip uses 3 connections points! One on each side plus we added a lower one to gice you more options!

This backmount clip with no teeth we placed a slight angle on the lower loops making this just a little easier to clip off to while your diving! Our lower plate we use a slight bend making it even easier to find when your reaching around! Plus we gave you two more side loops to clip too!

Overall width is roughly 4 1/4" inches wide at the widest point!

Length is roughly 4 1/4"

1/8" thick gives it still lightweight but strength 

Made from 304 stainless steel

Great for hanging smb's, liftbags or other items

We have tumbled this item for 48 hours to have all the edges be smooth and prevents any webbing damage

Made in the U.S.A. 

This backmount you use with 2" inch webbing. Perfect to use on your crotch strap for hanging items on your backside with no issues

Side clip off section are flat

Overall width is roughly 3 1/4" / 2 5/8" inches Long

Made from 304 stainless steel

This plate uses teeth for better gripping

Select flat or slightly angle bend on the side loops

This has been tumbled for 48 hours to have all the edges been smooth and prevents any webbing damage

Made in the U.S.A.

This backmount you use with 2" inch webbing. Our clip uses 3 connections points! One on each side plus we added a lower one to gice you more options!

This backmount clip with no teeth we placed a slight angle on both sides making this just a little easier to clip off to while your diving!

Overall width is roughly 4 1/4" inches wide at the widest point!

Length is roughly 4 1/4"

1/8" thick gives it still lightweight but strength 

Made from 304 stainless steel

Great for hanging smb's, liftbags or other items

We have tumbled this item for 48 hours to have all the edges be smooth and prevents any webbing damage

Made in the U.S.A. 

This backmount you use with 2" inch webbing. Perfect to use on your crotch strap for hanging items on your backside with no issues

This backmount clip with teeth we placed a slight angle on both sides making this just a little easier to clip off to while your diving!

Overall Length w/ bend: 7 1/4" inches

Overall width is roughly 2 1/2" inches wide

Made from 304 stainless steel

This plate uses teeth for better gripping

This has been tumbled for 48 hours to have all the edges been smooth and prevents any webbing damage

Made in the U.S.A.

This is our tec version of our long drop down D-Ring Piranha has you covered with diving hardware for anytype of diving including sidemount diving!

These have a special shape that allows you to configure your rig in many ways to make your diving needs

Made out of high quailty 304 marine grad stainless steel

These are tumbled for 48 hours to give a smooth surface and no rough edges to cut your webbing

These are made to be durable for anytype of diving you are wanting to do

Built so you can use these around your hip area, mount for use on your backend or anywhere you want an easy clip off!

Select from our dropdown box below!

These are made with either flat or a slight bend to allow you to clip off much easier

Fits 2" inch wide webbing

Overall Length: Roughly 5" inches

Overall Width: 2 3/8" inch

Thickness: 1/8" thick

So our newest piece of hardware just came in and if your looking for hanging items behind you well check out this piece!

Made of our stainless steel so you know salt or fresh water will not hurt it

1/8" Thick makes it durable

This is a straight mounting bracket with 2 large clip off loops on each side to better clear your back-side and makes it simply to find when reaching around

We made this with 4 slots so you can use 2 or 4 depending on what your diving and your needs

We have these tumbled for 48 hours giving them a smooth finish so as not to hurt your webbing thru the slot area

Overall length is roughly 6 3/4" inches

Loop Area is 1 7/8" long opening by 2 3/16" inches wide:: Inside measurement

Select flat or bent type from our drop down box below 

We have these made in the good ole USA!

• 1 1/2" Stainless Steel Swivel Bolt Snap
• High quality 316 marine grade Stainless 
• Great for Salt or fresh water use
• Easy underwater operation with or without gloves
• Large slide level for easy open or close!
• Must have for low visibility conditions
• 316 Stainless Steel
• Overall Length: 4 1/4" inches long / 1 1/2" ID Eye area / 7/16 gate opening! 
• This is the largest eye and with the butterfly slide makes it ideal for night diving, tec use and safety / rescue use! Using heavy gloves this slide is easy to open so no guessing even in murky waters!! This is a must try snap 

So here is a piece you can use in several locations based on your rig layout or needs!

We use 4 none teeth slots to hold in a stable location whereever you use it

Made out of our marine grade 304 stainless to reduce rusting

We tumble these for 48 hours to give all the edges a baby butt smooth finish so not to damage your webbing or any other part of your diving rig

This is a flat design piece 

We make these in the good ole Usa

Overall length: 5 15/16" inches long

Overall Width: 2 1/4" inches wide

1/8 Thick 304 Stainless

Works with all 2" inch webbing

Tear Drop Oval: 2 3/4" long