Enhanced Diver Safety with a Reliable Signal Buoy The Dive Alert Surface Marker Buoy DMB5 is a critical safety tool for open water, drift, and decompression diving. Engineered with Semi-Closed-Circuit one-way valve construction, this scuba diving surface marker buoy allows air inflation at depth or on the surface without air escaping. The DMB5 SMB functions as a highly visible scuba safety surface marker buoy and provides approximately 25 lbs of lift, adding redundancy during surface waits or emergency signaling. Designed for effortless deployment and visibility, this high-visibility dive safety marker should be in every diver's kit.
Built for Maximum Visibility and Durability With Solas reflective tape approved by the Coast Guard, the Dive Alert DMB5 SMB offers excellent visibility in daylight or low-light conditions. Constructed from tough 70 Denier polyurethane-coated nylon, this inflatable dive alert buoy resists wear across multiple dives. Dual nylon D-rings on the top and bottom allow you to attach lights, slates, or bolt snaps for added functionality. The connected configuration creates a surface flotation device, making this SMB for diving both versatile and reliable for varied underwater conditions.
Versatile Inflation with Smart Storage Design The DMB5 scuba diving safety signal buoy is equipped with an integrated oral inflator, LP hose inflator, and over-pressure valve with deflate cap. Whether inflating at depth or on the surface, the SMB with one-way valve ensures safe, consistent inflation and deflation. A built-in utility pocket houses the patent-pending spool, eliminating the need for a bolt snap to tie off while hanging. This compact, easy-to-use design ensures the Dive Alert surface marker buoy performs reliably without adding bulk to your gear.
Dive Alert Surface Marker Buoy DMB5 Features
One-way valve prevents air loss during inflation
Coast Guard approved Solas reflective tape for visibility
25 lbs of lift supports surface flotation when needed
70D polyurethane-coated nylon resists wear and tear
So we have a 5 foot long smb made from our tough 400 denier fabric to give you a quality product. This smb has many of the features for a safe dive
Orange on both sides with diver down on the front side of this smb!
We also have solas reflective tape nearthe top on both sides to aid when you need to be seen
We also have a stainless steel 1" inch D-ring located at the bottom to clip on to too
We also have a Over-Pressure Valve (OPV) locate near the bottom edge which prevents bursting and easy air dumping.
With our inflator tip you can choose to inflate by mouth or you can use a bc hose which will allow air in during the filling process and you just pull back and it will stop inflating with the hose. A simple but great and easy way to work your smb plus you can inflate from the bottom of this smb also so you re covered no matter how you wish to choose to inflate it
We have a plastic d-ring at the top so you can use a slate to let your dive boat what is going on or use a light to help the boat find you during evenings or night diving
This smb also uses what is called a duckbill or flapper valve to allow in but not release out until your done your dive.. Also at the where the air enters we have a pair of magnets to help keep your smb closed!
The finger spool pocket is large enough you can use of larger 150 foot finger spools or any size smaller! We use a zipper plus we have a 1" inch plastic snap clip to hold your pocket closed until you need to use it. Spool is NOT included with pocket!
We use a velcro strap to hold your smb closed until it is ready to use
Add a little flare from the rest of the pack with this fun surface marker! Whats better then nemo to let your dive boat know its you under the water alerting them
This surface marker is loaded with features! Why pay more when you can order from Piranha and get this special smb at an amazing price!!
6 Feet Length / 71" inches
5 7/8" Overall width
210 Denier with a urethane backing
Approximately 30+lbs of lifting capacity
Small compact design for easy storage with bungee to hold it rolled up and also a BUNGEE Loop to give you extra piece of mind
We use a velcro tab to secure your smb when folded up
Our smb has a oral / Bc hose inflator at the bottom or use a Bc hose to quickly inflate our Smb by either using your mouth or use a Bc inflator hose to fill this smb!
We use a 1" inch stainless steel D-ring at the bottom to clip off quickly
We also use solas reflective tape around the top to aid in spotting you on the surface no matter at which side you are on!
Non-Slip valve at bottom allows air into the smb and stay in without dumping out! "Flapper Valve/ Duckbill Valve"
Diver can fill the smb either by your regulator or mouth with the opening at the bottom or quick fill using a Bc hose on the quick fill nozzle
Lead weights located inside the smb at the bottom allows smb to stand straight up at the surface better than other smb's!
Also by having lead weights at the bottom the opening is easier to work with underwater
When rolled up we use a bungee to hold your Smb closed!!
We also use a larger over pressure relief button to prevent premature blow outs / failures and to remove air quickly when done using our Smb!
Our OPV also has a quick pull tab to dump air out if needed
So we have a 5 foot long smb made from our tough 400 denier fabric to give you a quality product. This smb has many of the features for a safe dive
Yellow on both sides with diver down on the front side of this smb!
We also have solas reflective tape nearthe top on both sides to aid when you need to be seen
We also have a stainless steel 1" inch D-ring located at the bottom to clip on to too
We also have a Over-Pressure Valve (OPV) locate near the bottom edge which prevents bursting and easy air dumping.
With our inflator tip you can choose to inflate by mouth or you can use a bc hose which will allow air in during the filling process and you just pull back and it will stop inflating with the hose. A simple but great and easy way to work your smb plus you can inflate from the bottom of this smb also so you re covered no matter how you wish to choose to inflate it
We have a plastic d-ring at the top so you can use a slate to let your dive boat what is going on or use a light to help the boat find you during evenings or night diving
This smb also uses what is called a duckbill or flapper valve to allow in but not release out until your done your dive.. Also at the where the air enters we have a pair of magnets to help keep your smb closed!
The finger spool pocket is large enough you can use of larger 150 foot finger spools or any size smaller! We use a zipper plus we have a 1" inch plastic snap clip to hold your pocket closed until you need to use it
We use a velcro strap to hold your smb closed until it is ready to use
So we have a 5 foot long smb made from our tough 400 denier fabric to give you a quality product. This smb has many of the features for a safe dive
Yellow on both sides with diver down on the front side of this smb!
We also have solas reflective tape nearthe top on both sides to aid when you need to be seen
We also have a stainless steel 1" inch D-ring located at the bottom to clip on to too
We also have a Over-Pressure Valve (OPV) locate near the bottom edge which prevents bursting and easy air dumping.
With our inflator tip you can choose to inflate by mouth or you can use a bc hose which will allow air in during the filling process and you just pull back and it will stop inflating with the hose. A simple but great and easy way to work your smb plus you can inflate from the bottom of this smb also so you re covered no matter how you wish to choose to inflate it
We have a plastic d-ring at the top so you can use a slate to let your dive boat what is going on or use a light to help the boat find you during evenings or night diving
This smb also uses what is called a duckbill or flapper valve to allow in but not release out until your done your dive.. Also at the where the air enters we have a pair of magnets to help keep your smb closed!
The finger spool pocket is large enough you can use of larger 150 foot finger spools or any size smaller! We use a zipper plus we have a 1" inch plastic snap clip to hold your pocket closed until you need to use it
We use a velcro strap to hold your smb closed until it is ready to use
Having a surface marker buoy (SMB) or lift bag along on a dive can come in real handy when things do not come out as planned.
Divers know that a surface marker buoy is either required by most professional dive operations for safety or having one is a very safe ideal
So having a pocket while diving is not an option, but really a requirement from a safety stand point.
Lift bags are great to have when you find something you need to retrieve from below and want a safe and dependable means to bring it back to the boat or beach.
Our mesh carry pouch is a convenient pouch to store your Smb or lift bag so it may be used for those just in time needs,
Our mesh carry pouch will accommodate our smb's "Not our 10 footer!" and small size liftbags "Not like 100+ lift ones would be tight" plus other manufactures buoys and bags.
Our mesh carry pouch is made from heavy-duty PVC coated nylon mesh with a full-length side opening using a hook and loop closure to secure your item and still being able to deploy.
Our pouch has 5 stainless-steel grommet holes for attachment of the pouch to your gear (mounting hardware SMB not included) and measures 6.5 x 14 in (16.5 x 35.5 cm)
Small compact design for easy storage with bungee to hold it rolled up or use the velcro strap and that will hold it rolled up! Or use both!!
Our smb has a oral / Bc hose inflator at the bottom or use a Bc hose to quickly inflate our Smb!!
Has a 1" plastic D-ring to attach a slate or light at the top of the Smb
We use a 1" inch stainless steel D-ring at the bottom to clip off quickly
Non-Slip duck valve at bottom allows air into the smb and stay in without dumping out! "Flapper Valve/ Duckbill Valve"
Diver can fill the smb either by your regulator or mouth with the opening at the bottom or quick fill using a Bc hose
Lead weights located inside the smb at the bottom allows smb to stand straight up at the surface better than other smb's plus help keep your duck valve closed
Also by having lead weights at the bottom the opening is easier to work with underwater
This is our Standard size Smb being just under 6" inches overall width and 6 feet long make this the perfect smb for any type of diving
When rolled up we use a bungee to hold your Smb closed and a velcro strap!!!
We also use a larger over pressure relief button to prevent premature blow outs / failures and to remove air quickly when done using our Smb!
Solas reflective tape is near the top on both sides plus the diver down is in reflective material to also help see you!
So here you go we have a High vis Pink camo color.. These are awesome looking smb's do not miss out while we have the limited amount in stock!!
6 Feet Length 6" X 72"
210 Denier with a urethane backing
Approximately 40+lbs of lifting capacity
Small compact design for easy storage with bungee to hold it rolled up or use the velcro strap and that will hold it rolled up! Or use both!!
Our smb has a oral / Bc hose inflator at the bottom or use a Bc hose to quickly inflate our Smb!!
Has a 1" plastic D-ring to attach a slate or light at the top of the Smb
We use a 1" inch stainless steel D-ring at the bottom to clip off quickly
Non-Slip duck valve at bottom allows air into the smb and stay in without dumping out! "Flapper Valve/ Duckbill Valve"
Diver can fill the smb either by your regulator or mouth with the opening at the bottom or quick fill using a Bc hose
Lead weights located inside the smb at the bottom allows smb to stand straight up at the surface better than other smb's plus help keep your duck valve closed
Also by having lead weights at the bottom the opening is easier to work with underwater
This is our Standard size Smb being just under 6" inches overall width and 6 feet long make this the perfect smb for any type of diving
When rolled up we use a bungee to hold your Smb closed and a velcro strap!!!
We also use a larger over pressure relief button to prevent premature blow outs / failures and to remove air quickly when done using our Smb!
Solas reflective tape is near the top on both sides plus the diver down is in reflective material to also help see you!
The new HOG 72in SMB with Low Profile Exhaust and Spool Combo Hi-Vis Orange is a game changer.
This SMB is lighter and more compact than any other 72in / 6ft SMB. And that includes it having a 33' spool.
With every method of inflation including inflator hose, manual and bottom feed there is no reason you cannot get this thing inflated.
It features a low profile over pressure exhaust built into the inflation tube which took years of R&D to develop and prevents damage to your smb from over inflation!
This SMB is smaller, lighter and more streamlined than almost all 3' SMBs on the market. Overall weight is just under 8oz and roughly 2 1/2" inches in diameter including the spool inside the pocket!
At the bottom they use a large delrin clip to quickly remove and / or secure your smb to your d-ring!
They also included a plastic d-ring at the top to secure a light stick or a slate to let the folks topside what is going on underwater
This design is easy to deploy with the finger spool already attached so making it one of the easest to release and use underwater! Also want more line you can either spool more on the spool already supplied or change it to one of our Alum 100 foot spools for even more line!!
The new HOG 72in SMB with Low Profile Exhaust and Spool Combo Hi-Vis Yelow is a game changer.
This SMB is lighter and more compact than any other 72in / 6ft SMB. And that includes it having a 33' spool.
With every method of inflation including inflator hose, manual and bottom feed there is no reason you cannot get this thing inflated.
It features a low profile over pressure exhaust built into the inflation tube which took years of R&D to develop and prevents damage to your smb from over inflation!
This SMB is smaller, lighter and more streamlined than almost all 3' SMBs on the market. Overall weight is just under 8oz and roughly 2 1/2" inches in diameter including the spool inside the pocket!
At the bottom they use a large delrin clip to quickly remove and / or secure your smb to your d-ring!
They also included a plastic d-ring at the top to secure a light stick or a slate to let the folks topside what is going on underwater
This design is easy to deploy with the finger spool already attached so making it one of the easest to release and use underwater! Also want more line you can either spool more on the spool already supplied or change it to one of our Alum 100 foot spools for even more line!!
The DiveAlert SMB (surface marker buoy) features Closed-Circuit construction, which prevents air spill at the surface. Inflate on the surface to attract visual attention or redundant flotation. Inflate at depth to send up as a surface marker.
Solas reflective tape (Coast Guard approved) across the top of SMB creates better visibility day and night. An Over-Pressure Valve (OPV) prevents bursting and easy air dumping. 45 inches long x 5 inches wide = approximately 8 lbs. of lift. Nylon D-ring on the top allows for easy attachment of a light or slate, along with a stainless steel D-ring at the bottom for attaching a spool or reel. 400 Denier polyurethane coated nylon material.
DURABLE CONSTRUCTION
Made of 400 Denier polyurethane coated nylon, this SMB will last dive after dive without issue. The nylon strap on the top allows for attachment of a light or slate.
UTILITY POCKET
The added pocket can be used for a finger spool, as an extra container, or to add weight for more stability in rough water.
INFLATOR VALVE
Inflation of the SMB can be done in any circumstance. You can inflate the DMB4P/S with your BC LP inflator hose, or by mouth via the stainless steel tip inflator valve or the plastic tip which can be used in the same manner!.
The DiveAlert SMB (surface marker buoy) features Closed-Circuit construction, which prevents air spill at the surface. Inflate on the surface to attract visual attention or redundant flotation. Inflate at depth to send up as a surface marker.
Solas reflective tape (Coast Guard approved) across the top of SMB creates better visibility day and night. An Over-Pressure Valve (OPV) prevents bursting and easy air dumping. 45 inches long x 5 inches wide = approximately 8 lbs. of lift. Nylon D-ring on the top allows for easy attachment of a light or slate, along with a stainless steel D-ring at the bottom for attaching a spool or reel. 400 Denier polyurethane coated nylon material.
DURABLE CONSTRUCTION
Made of 400 Denier polyurethane coated nylon, this SMB will last dive after dive without issue. The nylon strap on the top allows for attachment of a light or slate.
UTILITY POCKET
The added pocket can be used for a finger spool, as an extra container, or to add weight for more stability in rough water.
INFLATOR VALVE
Inflation of the SMB can be done in any circumstance. You can inflate the DMB4P/S with your BC LP inflator hose, or by mouth via the stainless steel tip inflator valve.
* With so many SMBs in the marketplace, it is easy to become confused. Some are “bare bones” proving difficult to use, while others are overbuilt, more suited for extreme expeditions. This Marker Buoy (SMB) adds all the right features
Features:
6 ft (183 cm) length/large 12 in (30.5 cm) circumference
Lower pocket accommodates a lead weight or finger spool
Open bottom with anti-spill baffle
Combination oral and BC QD inflation
Overpressure relief valve w/ manual pull cord
SOLAS reflective tape on both sides
Note: Like all of Piranha's Dive Products we warranty them from manufacturing defects!
Have an issue or question with this or any of our products please feel free to email us at Piranhadivemfg@yahoo.com
to get your question or issue answered.
If we need to get your item replaced Piranha will replace your item with a new item based on what you have addressed as a concern to us.
These Items have a limited warranty for 12 months from date of purchase so always keep your invoice number to allow us to verify
Deploying a marker buoy from depth has its challenges and here could make your dive a little easier? Also new to launching a surface marker buoy? This will make your learning much quicker and safer
KEY FEATURES
Easy Deploy Design
Simplifies Procedure
Just Add Air & Let-It-Fly
Provides Excellent Visibility
Over-Pressure Relief Valve w/Pull Cord
Purpose
Surface Marker Buoy
Materials
Buoy: Urethane Laminated Fabric
Dimensions (L x Circumference)
6' x 12" (183 x 30.5cm)
Color
Multiple
Inflation (Valve)
Combination Oral & QD Hose Inflation
Over Pressure Relief Valve
Yes
Manual Dump Valve
Yes
Finger Spool Included!
Material
Molded
Line Length
50' (15m) WHITE Lline
Attachment Point
D-Ring
Securing a line spool and SMB, connecting them together, deploying them, all while maintaining neutral buoyancy and holding on to other gear, has overwhelmed many a diver.
The Fast Launch Marker Buoy simplifies the procedure! The line spool is stored within the marker buoy and is already connected to it! Just add air and let it fly. 6' (183cm) in length with a large 12" (30.5cm) circumference provides excellent visibility when deployed on the surface.
Lower pocket includes a spool with 50' (15m) of line. Spool line is attached to D-ring inside the pocket.
Open bottom with anti-spill baffle plus also has a Combination oral and QD hose inflation.
Over-pressure relief valve with pull cord prevents your smb from damage when air expands!
SOLAS reflective tape on both sides increases visibility in low light or night conditions.
The Fast Launch Marker Buoy rolls up to a compact size and is secured with a squeeze-style side-release buckle.
Note: Like all of Piranha's Dive Products we warranty them from manufacturing defects!
Have an issue or question with this or any of our products please feel free to email us at Piranhadivemfg@yahoo.com
to get your question or issue answered.
These Items have a limited warranty for 12 months from date of purchase so always keep your invoive number to allow us to verify
When surface visibility is important, such as performing stops during deco or surfacing after a drift dive
The New Piranha Dive all black Smb gives you or your dive boat a very different way to spot a diver on the surface! We also highly recommend a whistle to grab the dive boat's attention or fellow divers that maybe a distance from you
The Piranha Dive 36" inch Foot Surface Marker is an essential dive accessory and is perfect for emergency situations!!
The Surface Marking Tube makes sure divers can be seen in open ocean where waves, surface reflection and noisy boat motors can make it difficult to be noticed
An over pressure relief valve eliminates over inflation and premature failures
These are a closed bottom SMB!
Our Smb's have a reflective outer edge!
We also use a 1" D-ring Stainless Steel at the bottom to clip off too
You can fill these by oral inflation or use a Bc hose for a controlled fill!
Small enough so it will fit into a small pocket or just clip it off!
You are purchasing an all BLACK Smb!
NOTE: Our All BLACK smb when rolled up is held closed by a bungee you loop around the smb!
Never use a black Smb? This is the time to try them out and see what we noticed when out on the water! We really loves these and brought them in!!
Our Hog 36" inch dual colored smb will allow you to be spotted in the ocean or large lakes!
Hog's newest color combo! Being one side is Orange and the other side is Yellow making this smb the best of all worlds! Being spotted with this color combo is much higher!!
210 Denier with a urethane backing
Approximately 40lbs of lifting capacity
Small compact design for easy storage with velcro to hold it rolled up
Our smb has a oral / Bc hose nipple inflator valve near the bottom
Has reflective tape near the top to aid in spotting you on the surface!
Has an over pressure relief button to prevent premature blow outs / failures
The DiveAlert SMB (surface marker buoy) features Closed-Circuit construction, which prevents air spill at the surface. Inflate on the surface to attract visual attention or redundant flotation. Inflate at depth to send up as a surface marker.
Solas reflective tape (Coast Guard approved) across the top of SMB creates better visibility day and night. An Over-Pressure Valve (OPV) prevents bursting and easy air dumping. 45 inches long x 5 inches wide = approximately 8 lbs. of lift. Nylon D-ring on the top allows for easy attachment of a light or slate, along with a stainless steel D-ring at the bottom for attaching a spool or reel. 400 Denier polyurethane coated nylon material.
DURABLE CONSTRUCTION
Made of 400 Denier polyurethane coated nylon, this SMB will last dive after dive without issue. The nylon strap on the top allows for attachment of a light or slate.
UTILITY POCKET
The added pocket can be used for a finger spool, as an extra container, or to add weight for more stability in rough water.
INFLATOR VALVE
Inflation of the SMB can be done in any circumstance. You can inflate the DMB4P/S with your BC LP inflator hose, or by mouth via the stainless steel tip inflator valve.
The DiveAlert SMB (surface marker buoy) features Closed-Circuit construction, which prevents air spill at the surface. Inflate on the surface to attract visual attention or redundant flotation. Inflate at depth to send up as a surface marker.
Solas reflective tape (Coast Guard approved) across the top of SMB creates better visibility day and night. An Over-Pressure Valve (OPV) prevents bursting and easy air dumping. 45 inches long x 5 inches wide = approximately 8 lbs. of lift. Nylon D-ring on the top allows for easy attachment of a light or slate, along with a stainless steel D-ring at the bottom for attaching a spool or reel. 400 Denier polyurethane coated nylon material.
DURABLE CONSTRUCTION
Made of 400 Denier polyurethane coated nylon, this SMB will last dive after dive without issue. The nylon strap on the top allows for attachment of a light or slate.
UTILITY POCKET
The added pocket can be used for a finger spool, as an extra container, or to add weight for more stability in rough water.
INFLATOR VALVE
Inflation of the SMB can be done in any circumstance. You can inflate the DMB4P/S with your BC LP inflator hose, or by mouth via the stainless steel tip inflator valve.
Our Hog 45" inch dual colored smb will allow you to be spotted in the ocean or large lakes!
Hog's newest color combo! Being one side is Orange and the other side is Yellow making this smb the best of all worlds! Being spotted with this color combo is much higher!!
210 Denier with a urethane backing
Approximately 40lbs of lifting capacity
Small compact design for easy storage with velcro to hold it rolled up
Our smb has a oral / Bc hose inflator nipple near the bottom
Has reflective tape near the top to aid in spotting you on the surface!
Has an over pressure relief button to prevent premature blow outs / failures
When surface visibility is important, such as performing stops during deco or surfacing after a drift dive
The HOG 45" inch Foot Surface Marker is an essential dive accessory
The Surface Marking Tube makes sure divers can be seen in open ocean where waves, surface reflection and noisy boat motors can make it difficult to be noticed
An over pressure relief valve eliminates over inflation and premature failures
These are a closed bottom SMB!
You can fill these by oral inflation or use a Bc hose for a controlled fill!
A very compact size to fit into your BCD pocket or clip it off to make carrying this Smb easy and simple
NOTE: A Velcro Strap keeps this Smb rolled up tightly for you!
When surface visibility is important, such as performing stops during deco or surfacing after a drift dive
The Piranha Dive Mfg 45" inch Foot Surface Marker is an essential dive accessory
The Surface Marking Tube makes sure divers can be seen in open ocean where waves, surface reflection and noisy boat motors can make it difficult to be noticed
An over pressure relief valve eliminates over inflation and premature failures
These are a closed bottom SMB!
You can fill these by oral inflation or use a Bc hose for a controlled fill!
A very compact size to fit into your BCD pocket or clip it off to make carrying this Smb easy and simple
When surface visibility is important, such as performing stops during deco or surfacing after a drift dive
The Piranha Dive Mfg 45" inch Foot Surface Marker is an essential dive accessory
The Surface Marking Tube makes sure divers can be seen in open ocean where waves, surface reflection and noisy boat motors can make it difficult to be noticed
An over pressure relief valve eliminates over inflation and premature failures
These are a closed bottom SMB!
You can fill these by oral inflation or use a Bc hose for a controlled fill!
A very compact size to fit into your BCD pocket or clip it off to make carrying this Smb easy and simple
When surface visibility is important, such as performing stops during deco or surfacing after a drift dive
The Piranha Dive Mfg 45" inch Foot Surface Marker is an essential dive accessory
The Surface Marking Tube makes sure divers can be seen in open ocean where waves, surface reflection and noisy boat motors can make it difficult to be noticed
These are a closed bottom SMB!
You can fill these by oral inflation only
A very compact size to fit into your BCD pocket or clip it off to make carrying this Smb easy and simple
We have a closed 45" smb but this time we had added an OPV
*Why you ask an opv? Simple you can inflate this smb at any depth and the opv will release any over pressure protecting your tube from any expanding air. We use a smaller opv 1" diameter on our smb to help keep the profile small and compact!!
*This is a 5" inch wide by 45" inches long
*We also added a dual inflation valve on this smb. You can inflate by mouth or hose a Bc hose and by pressing on the valve it will inflate the smb and you can pull away with no issues since the valve does not grab and hold your hose!
*We use a valcro strap to hold it closed when not in use
*Lastly we added a 1" inch stainless steel d-ring to clip off too
*This is a great compact smb with all the little details the big guys have but at a lower cost and smaller foot print
* Use for Rebreather, extended range, and sidemount divers that have different requirements for a DSMB than recreational divers.
* From the heavy-duty 420D nylon fabric to the over-sized stainless attachment D-ring on the bottom, this DSMB is a quality product purposefully designed with the technical diver in mind.
Closed bottom design - 45 in (114 cm) length x 10 in (25.4 cm) circumference
The stainless steel tipped inflator allows oral or QD hose inflation
2 in (5 cm) wide SOLAS reflector tape all the way around
2 x 4 in (5 x 10 cm) white panel at the top to write on with a permanent marker
1.5 in (38 mm) over-pressure valve with pull cord for easy deflation and roll-up
Reusable safety sausage with a unique two-layer design: the outer layer is made of tough nylon with water-resistant PU coating, which protects the inner bladder.
Made from heavy duty 420D Nylon with water-resistant PU coating which protects the inner bladder from punctures!
The taped edge prevents the outer layer from fraying.
To inflate underwater, simply use an octopus to release air into the balloon's opening, and the air cell's special enclosure will automatically trap all incoming gas.
The Smb has counter weights to help it staying upright.
Smb Length: 54" inches / 137cm
Comes with a sturdy storage pouch that has a mesh bottom for quick drainage.
It can be carried on any 2" webbing or clipped onto a d-ring with its plastic clip!
Automatic valve releases excess pressure to prevent this smb from bursting or damage!
The DiveAlert SMB (surface marker buoy) features Closed-Circuit (one-way valve) construction, which prevents air spill at surface. Inflate on the surface to attract visual attention or redundant flotation. Inflate at depth to send up as a surface marker. Solas reflective tape (Coast Guard approved) across top of SMB creates better visibility day and night.
NOTE: The picture is of an ORANGE DMB1 Smb but you are purchasing a yellow one!
Over-Pressure Valve (OPV) prevents bursting and easy air dumping.
Deluxe SMB is 65″ long by 8″ wide (165 x 20 cm) which provides approximately 40 lbs. (18.1 kg) of lift.
Nylon strap handle on top allows for easy attachment of light or slate.
Material : 400 Denier Polyurethane Coated Nylon. Color : High Visibility Safety YELLOW. Dimensions : 65″ Long By 8″ Wide (165 X 20 Cm). Buoyancy: Approximately 40 Lbs. (18.1 Kg). Weight [with packaging] 0.65 lb
Deploying a marker buoy from depth has its challenges and here could make your dive a little easier? Also new to launching a surface marker buoy? This will make your learning much quicker and safer
KEY FEATURES
Easy Deploy Design
Simplifies Procedure
Just Add Air & Let-It-Fly
Provides Excellent Visibility
Over-Pressure Relief Valve w/Pull Cord
Purpose
Surface Marker Buoy
Materials
Buoy: Urethane Laminated Fabric
Dimensions (L x Circumference)
6' x 12" (183 x 30.5cm)
Color
Multiple
Inflation (Valve)
Combination Oral & QD Hose Inflation
Over Pressure Relief Valve
Yes
Manual Dump Valve
Yes
Finger Spool Included!
Material
Molded
Line Length
50' (15m) WHITE Lline
Attachment Point
D-Ring
Securing a line spool and SMB, connecting them together, deploying them, all while maintaining neutral buoyancy and holding on to other gear, has overwhelmed many a diver.
The Fast Launch Marker Buoy simplifies the procedure! The line spool is stored within the marker buoy and is already connected to it! Just add air and let it fly. 6' (183cm) in length with a large 12" (30.5cm) circumference provides excellent visibility when deployed on the surface.
Lower pocket includes a spool with 50' (15m) of line. Spool line is attached to D-ring inside the pocket.
Open bottom with anti-spill baffle plus also has a Combination oral and QD hose inflation.
Over-pressure relief valve with pull cord prevents your smb from damage when air expands!
SOLAS reflective tape on both sides increases visibility in low light or night conditions.
The Fast Launch Marker Buoy rolls up to a compact size and is secured with a squeeze-style side-release buckle.
Note: Like all of Piranha's Dive Products we warranty them from manufacturing defects!
Have an issue or question with this or any of our products please feel free to email us at Piranhadivemfg@yahoo.com
to get your question or issue answered.
These Items have a limited warranty for 12 months from date of purchase so always keep your invoice number to allow us to verify
With so many SMBs in the marketplace, it is easy to become confused. Some are “bare bones” proving difficult to use, while others are overbuilt, more suited for extreme expeditions.
The pocketed Surface Marker Buoy (SMB) adds all the right features with a lower pocket to hold a spool or even weight
Features:
6 ft (183 cm) length/large 12 in (30.5 cm) circumference
Lower pocket accommodates a lead weight or finger spool
Open bottom with anti-spill baffle
Combination oral and BC QD inflation
Overpressure relief valve w/ manual pull cord
SOLAS reflective tape on both sides
Note: Like all of Piranha's Dive Products we warranty them from manufacturing defects!
Have an issue or question with this or any of our products please feel free to email us at Piranhadivemfg@yahoo.com
to get your question or issue answered.
These Items have a limited warranty for 12 months from date of purchase so always keep your invoive number to allow us to verify
Hog's newest color combo! Being one side is Orange and the other side is Yellow making this smb the best of all worlds! Being spotted with this color combo is much higher!!
210 Denier with a urethane backing
Approximately 40lbs of lifting capacity
Small compact design for easy storage with velcro to hold it rolled up
Our smb has a oral / Bc hose inflator at the bottom
Has reflective tape near the top to aid in spotting you on the surface!
Non-Slip valve at bottom allows air into the smb and stay in without dumping out! "Flapper/Duck Valve"
Diver can fill the smb either by your regulator or mouth with the opening at the bottom
Has an over pressure relief button to prevent premature blow outs / failures
* With so many SMBs in the marketplace, it is easy to become confused. Some are “bare bones” proving difficult to use, while others are overbuilt, more suited for extreme expeditions.
The Pocketed Surface Marker Buoy (SMB) adds all the right features with a pocket to hold a spool or weight
Features:
6 ft (183 cm) length/large 12 in (30.5 cm) circumference
Lower pocket accommodates a lead weight or finger spool
Open bottom with anti-spill baffle
Combination oral and BC QD inflation
Overpressure relief valve w/ manual pull cord
SOLAS reflective tape on both sides
Note: Like all of Piranha's Dive Products we warranty them from manufacturing defects!
Have an issue or question with this or any of our products please feel free to email us at Piranhadivemfg@yahoo.com
to get your question or issue answered.
These Items have a limited warranty for 12 months from date of purchase so always keep your invoice number to allow us to verify
Deploying a marker buoy from depth has its challenges and here could make your dive a little easier? Also new to launching a surface marker buoy? This will make your learning much quicker and safer
KEY FEATURES
Easy Deploy Design
Simplifies Procedure
Just Add Air & Let-It-Fly
Provides Excellent Visibility
Over-Pressure Relief Valve w/Pull Cord
Purpose
Surface Marker Buoy
Materials
Buoy: Urethane Laminated Fabric
Dimensions (L x Circumference)
6' x 12" (183 x 30.5cm)
Color
Multiple
Inflation (Valve)
Combination Oral & QD Hose Inflation
Over Pressure Relief Valve
Yes
Manual Dump Valve
Yes
Finger Spool Included!
Material
Molded
Line Length
50' (15m) WHITE Lline
Attachment Point
D-Ring
Securing a line spool and SMB, connecting them together, deploying them, all while maintaining neutral buoyancy and holding on to other gear, has overwhelmed many a diver.
The Fast Launch Marker Buoy simplifies the procedure! The line spool is stored within the marker buoy and is already connected to it! Just add air and let it fly. 6' (183cm) in length with a large 12" (30.5cm) circumference provides excellent visibility when deployed on the surface.
Lower pocket includes a spool with 50' (15m) of line. Spool line is attached to D-ring inside the pocket.
Open bottom with anti-spill baffle plus also has a Combination oral and QD hose inflation.
Over-pressure relief valve with pull cord prevents your smb from damage when air expands!
SOLAS reflective tape on both sides increases visibility in low light or night conditions.
The Quick Launch Marker Buoy rolls up to a compact size and is secured with a squeeze-style side-release buckle.
Note: Like all of Piranha's Dive Products we warranty them from manufacturing defects!
Have an issue or question with this or any of our products please feel free to email us at Piranhadivemfg@yahoo.com
to get your question or issue answered.
These Items have a limited warranty for 12 months from date of purchase so always keep your invoice number to allow us to verify
So we have a pocket that you can use for so many diving applications only your imagination will stop you!
It can hold a finger spool and 6 foot /72" inch smb with no problems!
Can hold a small light / strobe!
As great drainage mesh on the larger pocket
Has a grommet for drainage on the front smaller pocket
Small pocket on the front has a clear window for viewing On the backside we use a 2" inch loop to slide onto your webbing or a plastic clip to clip off on your rig!
Standard Features:
420 denier nylon and PVC mesh
YKK #5 Delrin zipper and slider on both pockets
Attaches by sliding over the end of any 2" webbing or clip off using plastic snap at top
This Rubber Air nozzle is a great little tool for your save-a-dive kit or your toolkit plus got a flat tire no more worrying you can grab your scuba tank and fill it!
This nozzle connects in-line on your BC Inflator Hose and puts out powerful, directed air at just the push of the thumb operated valve.
This tool is completely water safe, so it would be a great little tool to use for inflating lift bags or safety sausages while underwater.
We got our deluxe model with the tire inflator so now you can have just one tool to solve 2 problems!!
A must have little item for every diver and at our price you just can't beat it!
Have an old tip that needs replacing? or you want the tip you can screw on and use with your inflator hose with!
This is a complete stainless steel inflator you can use with your Bc hose to help inflate your liftbag or smb
Carry one or more just in case yours goes bad or breaks
Edges are smooth so no sharp edges
Design for spearfishing divers when the plastic tips will snap or break these will hold up even with the tough gets going these make sure your fish or other items return safetly. When durability counts these are the filler tips you want!
Have an old tip that needs replacing? or you want the tip you can screw on and use with your inflator hose with! This is the tip you want in the metal version!
This just can screw on in place of your older tip you may have on your surface marker buoy or lifgbag!
Carry one or more just in case yours goes bad or breaks
Have an old tip that needs replacing? or you want the tip you can screw on and use with your inflator hose with! This is the tip you want in the plastic
This just can screw on in place of your older tip you may have on your surface marker buoy or lifgbag!
Carry one or more just in case yours goes bad or breaks
When surface visibility is important, such as performing stops during deco or surfacing after a drift dive
Our new Piranha Dive model makes it adfordable now to get one at a price you can afford and is an essential dive accessory
The Surface Marking Tube makes sure divers can be seen in open ocean where waves, surface reflection and noisy boat motors can make it difficult to be noticed
We used a smaller profile over pressure relief valve "OPV" and that eliminates over inflation and premature failures
We use a lower profile OPV to still protect your smb from damage by allowing air to escape
We also use a 1" D-ring Stainless Steel at the bottom to clip off too
These are a closed bottom SMB but can be used at depth because of our opv valve
You can fill these by oral inflation or use a Bc hose for a controlled fill!
A very compact size to fit into your BCD pocket or clip it off to make carrying this Smb easy and simple
Made out of a tough 210D nylon fabric material
45" inches long by roughly 5" inches wide
NOTE: We use a velcro strap to keep this Smb rolled up tightly for you while being stored!
Want to make your liftbag, Smb, Bc or almost anything reflective? With this tape you can and this will stick to your fabric with no issues. If a corner starts to peel just use a little aqua-seal and it will never move
This stuff is awesome and just try it and see what we are talking about
Now you can be seen and you can add this to your Bc even!
Now that more training agencies are requiring that your Surface Marker Buoy have reflective tape we have a solution for you!
Don't go unnoticed. When you need to increase visibility and decrease risk reach for Tenacious Tape Reflective Fabric Tape by Gear Aid.
Tenacious Tape Reflective Tape utilizes glass bead reflective technology to reflect light better than any colored or fluorescent tape. Stick it on pet accessories, bikes, vehicles, backpacks, clothing or footwear. The ultra-aggressive adhesive sticks to almost any surface without peeling and the durable and waterproof fabric performs in both wet and dry conditions.
Offering enhanced visibility and safety at night or in low-light conditions, Tenacious Tape Reflective Fabric Tape meets ANSI/ISEA 107 standard for high-visibility safety apparel as required by the Federal Highway Administration (FHWA).
Features
Highly reflective tape with glass bead technology
White reflective fabric enhances visibility and safety
Easy to apply (peel and stick)
Aggressive adhesive sticks to almost anything
Clean adhesive technology won't leave a sticky residue if removed
Safety marking for vehicles, bikes, clothing, backpacks, helmets, boats, footwear, pet accessories and more
Includes 3" x 20" strip
Customizable; grid backing allows for straight lines
Performs well in both wet and dry conditions
Machine washable
Waterproof, weatherproof and durable
Flexible tape conforms to shapes and corners without peeling or lifting
Smooth and lightweight fabric
Meets ANSI/ISEA 107 standard for high-visibility safety apparel as required by the Federal Highway Administration (FHWA)
This new D-Ring we now have added a 3rd option for clipping to/from! We added a low profile D-ring at the bottom to allow for even more flexibility to your rig!!
You can use this has a triple under the counterlung d-ring or slide it on your 2 inch crotch strap towards the rear and now you have a place to attach spools, reels or even Smb / liftbags and even more with the 3rd low profile rear D-ring!!!
Fits 2 inch webbing... measures loop 2 inch "ID" w/ 1.5 inch long "ID"
With our latest storage pocket you can store it behind you using our 2 stainless steel grommets that are spaced 5 5/8" inces apart or we added on the backside where you can slide yourr 2" inch webbing through it to store it another way / place
Depending on how you use this pocket you can store surface markers or liiftbags? and you can secure the open end by using the velcro to close the pocket
Want to use a surface marker with a finger spool? No problem with the webbing slot on the back side you can use ths pocket that way in a vertical layout
You can even store your back-up mask if you choose or your light?
This pocket has has a drainage grommet to help remove water quickly when not in use
Llightweight denair material gives you strength and also allows your pocket to quiickly dry when not in use
You can also purchase lockig clips to hold your pocket in place so it is not sliding around or quick links if using to hang off your backend!
Dimensions are:
Length" 10" inches of inside usable space with a 4 3/4" inch diameter allowing you to use this pocket in many ways
You can use this has a double under the counterlung d-ring or slide it on your 2 inch crotch strap towards the rear and now you have a place to attach spools, reels or even Smb / liftbags!
Fits 2 inch webbing... measures loop 2 inch "ID" w/ 1.5 inch long "ID"
This bag allows a diver to signal their location and make a safety stop when off the upline!
Buoy can carry a maximum weight of roughly 25+ lbs but has enough lift to support a diver when making their safety stop
Comes complete with a pouch for storage, Pouch sizing is 8" X 3.75" compact nylon carry bag and the bag has both a plastic clip or webbing sewn on the back so you can slide it on your harness!
Includes line attached to the pouch and bag for easy handling and deploying
Open type bottom of bag that closes the throat automatically when inflated
Has a swivel brass boat snap at the bottom of the bag for attaching items!
Having a surface marker buoy (SMB) or lift bag along on a dive can come in real handy when things do not come out as planned.
Divers know that a surface marker buoy is either required by most professional dive operations for safety or having one is a very safe ideal
So having a pocket while diving is not an option, but really a requirement from a safety stand point.
Lift bags are great to have when you find something you need to retrieve from below and want a safe and dependable means to bring it back to the boat or beach.
Our mesh carry pouch is a convenient pouch to store your Smb or lift bag so it may be used for those just in time needs,
Our mesh carry pouch will accommodate our smb's "Not our 10 footer!" and small size liftbags "Not like 100+ lift ones would be tight" plus other manufactures buoys and bags.
Our mesh carry pouch is made from heavy-duty PVC coated nylon mesh with a full-length side opening using a hook and loop closure to secure your item and still being able to deploy.
Our pouch has 5 stainless-steel grommet holes for attachment of the pouch to your gear (mounting hardware not included) and measures 6.5" x 12" (16.5cm x 30.5cm).
We have these fun mini smb's to play with! These are very limited in stock right now so grab one and have some fun with them
They are roughly 9 3/4" inches long on the inflatable part of this smb
Overall length is roughly 13" inches
Roughly 2 1/2" wide
Has a bungee to roll this little guy up and a plastic rotating clip to clip off and carry them
To blow these up you have to depress the inflator mouthpiece and blow into it! Simple release and its fill ready for your dive
Piranha's Price: $7.29
Surface Marker Buoys for Every Kind of Dive
Be seen from the boat. Our SMBs run from 5 foot to 6 foot in safety orange, yellow, pink and blue or pink camo, with flapper and duck valve bottoms, and many include a finger spool pocket so your spool travels with the bag. Mesh SMB and liftbag pouches are here too, including an extra-long 6.5 by 14 inch version for bulkier bags.
