We now offer out latest request to make a triple slot with no teeth and a slightly longer D Ring loop and we have what you can use for your chest strap or use a split ring and add other items to this D ring
We have these machine cut
These are tumbled for 48 hours giving these smooth edges!
Fits upto 2" inch wide webbing
Slots are smooth and you can run 2 pieces of webbing if you want too
So you can get these in 3 configurations! Flat, slightly bent or a 90 degree angle just select from our drop down box below on what you wish to get
We have a new Keep Diving Tec backplate made out of aluminum T6061
We only brought in a limited number after we tested this product to see who diver's like this design
This is an awesome backplate for everyday diving or if you want to travel take this plate along since it is lightweight but has all the features of those more expensive plates on the market today
This high performance aluminum tec scuba diving back plate is lightweight and durable with high strength with strong corrosion resistant and wear-resistant
The outside edge "Perimeter" has side holes for mounting lights, tank bottles, lift bags and other accessories
Has 4 slots to route cam straps for the best balance when diving with a single tank for even more adjustments in your trim
Has 1 slot for use with the standard 2" inch slot crotch straps
Using for doubles no problem with have 3 alignment holes near the top with a full open slot near the bottom so sliding your tanks bolts a as easy as 123!
Bult with a deep channel so your bolts will not stick you in your back! This plate is very comfortable to wear and a breeze to set-up your harness to it
Built for use with 2" inch wide webbing.
Specification:
- Material: High strength T6061 Aluminum
- Size (L x W): Approx. 15.43" inches / 392MM (Length) * Almost 11" inches / 278MM (Wide) and 3MM (Thick)
1 Inch crotch strap works with our backplates and any with 1" inch slot on the backplate
Our 1" inch crotch strap runs from the adjustable part of the strap on the rear to mount to the slot in the backplate to the front where the loop goes on the waist belt webbing at the front of your harness both have 1" inch plastic sliders allowing you to adjust your crotch strap
Using this crotch strap helps to maintain your harness from moving up on our body during a water entry from a boat or while ascending during your dive. Also by holding your rig in place this prevents your cylinders/valves from contacting your head
We use a plastic 1" inch slide release buckle which allows a diver to quickly release it during an emergency situation
The 1" Inch strap is used by many divers for its comfort and offers the convenience of being adjusted quickly to any diver
This crotch strap does not have a scooter ring since a 1" inch strap is to narrow if you are looking to clip off or use with a scooter we recommend using our 1 1/2" or 2" inch crotch straps which are better suited for that application
Our 2 Inch crotch strap works with our backplates and many others on the market today!
Our 2 inch crotch strap runs from the adjustable part of the strap on the rear to mount to the slot in the backplate to the front where the loop goes on the waist belt webbing at the front of your harness and we use a plastic quick release buckle to quickly get out of your rig!
Using this crotch strap helps to maintain your harness from moving up on our body during a water entry from a boat or while ascending during your dive. Also by holding your rig in place this prevents your cylinders/valves from contacting your head
Our strap has a 2 inch stainless steel scooter ring for use with diver propulsion vehicles at the front of the strap right below the webbing loop.
You can also use this 2 inch scooter ring for applications such as a temporarily place to clip off an item such as reels, dive lights, spools or camera's.
On the backside of the strap we have a place for a 5mm 6mm stainless steel d-ring that uses a slider so you can adjust it for your final positioning.. You can purchase this d-ring from our drop down box below
We use a 2" inch soft black webbing so it does not cut into your wetsuit material or cause any damage that stiffer webbing can cause
The 2 inch webbing creates a distribution of weight because of the width provides a greater secure feeling during those dives
Our Quick adjust 2" inch slider make donning on or off your harness a breeze with our newest piece!
Made out of SS304 stainless steel with a colored aluminum bar.
Now you ask what is the 15mm? That is the height and thickness of the aluminum bar since we have a 12mm in pink also which is slight lower and thinner bar. The height really depends on what you feel you want to use with your webbing
These do have small serrated teeth and really only grab when in use and not when donning your harness
So plenty of harness diver's have struggle to put on and remove their continuous loop harness set-ups because for many reasons but we have a simple solution now for you. Piranha now has our harness loop adjustment slider loop which makes putting on or removing from a one piece harness set-up simple and quick! Our harness loop adjustment slider ring fits all 2" / 50mm webbing Piranha Dive Mfg. sells!
Our loop adjustment slider ring allows your shoulder strap of webbing more easily adjustable on your backplates
Our loop adjustment slider ring allows your left shoulder strap of any 2-inch / 50mm continuous webbing harness to be freely adjustable, making your harness much easier to use.
Our loop adjustment slider ring is simply to install and use without cutting your webbing,
Divers using drysuits or heavy 7mm wetsuits will especially find using our loop adjustment ring a simple solution to a problem plus diver's with limited shoulder mobility
Our loop adjustment slider ring is made out of marine grade stainless steel to reduce rust formations
Our loop adjustment slider ring works with a 2-inch 50mm continuous webbing harness with most backplates
To assembly this loop adjustment ring you simple start your assembly of your webbing harness just insert the ring into the back of the diver's left waistband slot on the plate prior to threading the webbing. Instead of weaving the left side of the harness waistband through the plate, simply thread it through the loop adjustment slider ring.
Your left shoulder webbing will become easy to slide and making it adjustable to better get a tight fit to your divingrig rig. If your harness is built already simple remove the one side to place the loop adjustment ring in place
We recommend using only one loop adjustment slider ring on your leftside of your dive harness but you can always purhase two and play with the set up to see if you find a totally adjustable set up. We have played with two and found that using the leftsided one works best for most divers
NOTE: When you purchase our loop adjustment slider ring from us you will recive one Loop Adjustment Slider ring!!!!
If your using stiff webbing this will reduce your webbing from cutting into your neoprene or even a drysuit
Even our standard webbing will work with this product and give more protection to our rig
Special designs allows you to fit any 2" inch webbing area
Our sleeve is roughly 15" inches long
You just slide this sleeve over your webbing giving a nice padded area. Using a scooter this pad will take all the pressure off your bottom!!
We also found you can cut these into smaller pieces and use them on your harness to locate hardware or even use them as shoulder pads just order 2 of them and slide them on!
Another great little piece of hardware we made per a customer request!
This has a 3 divided slot area
We also have a hole for your 3/16" Bungee cord
These are made for either your shoulder straps or run them along your waist to quickly clip off
Made with our special gripper teeth so not to damage your webbing but give you a little more grip
These are made out of 304 marine grade hardware so you know these are highly rust resistantance
And yes these are tumbled for 48 hours giving them a smooth edge with nothing sharp to cut your webbing
NOTE: If you select the hole to your leftside then understand that when looking at your rig the hole would be on the right. So looking at that hole your righthand would grab it. Hope we are giving you enough info. Look at the bungee hole in the picture on the wwebsite and that is a right side hole
We are proud to offer our newest color! Safety ORANGE.. It has taken years to find this underwater webbing with all the right features. We love adding colors to our dive rigs too make us stand out from the crowd and know our diving rig verses another diver!
This orange color is like our smb's orange color which is just the right brightness for visability when diving We use a professional grade of nylon webbing which can be used for many applications
Our webbing is a on the is what we called standard stiffness which is used mainly for harnesses and weight belts becuase it has some flexibility but also is slightly flexible. A great webbing to use
This webbing is just softer in flex than our med stiff red and other color webbing
Used for weight belts and other applications
Our webbing is made to be more durable for underwater use making it last longer and works better on weight belts, harnesses and backstraps and cam straps!
This webbing is design for marine use and will hold up very well with underwater use
We are proud to offer our newest color! Safety YELLOW.. It has taken years to find this underwater webbing with all the right features. We love adding colors to our dive rigs too make us stand out from the crowd and know our diving rig verses another diver!
This is a perfect color of not a neon yellow color or a goldish color but yet gives you a great looking harness or other items we build with this color!
We use a professional grade of nylon webbing which can be used for many applications
Our webbing is a on the is what we called standard stiffness which is used mainly for harnesses and weight belts becuase it has some flexibility but also is slightly flexible. A great webbing to use
This webbing is just softer in flex than our med stiff red and other color webbing
Used for weight belts and other applications
Our webbing is made to be more durable for underwater use making it last longer and works better on weight belts, harnesses and backstraps and cam straps!
This webbing is design for marine use and will hold up very well with underwater use
We are proud to offer our newest color! Soft PINK.. It has taken years to find this underwater webbing with all the right features. We love adding colors to our dive rigs too make us stand out from the crowd and know our diving rig verses another diver!
Thiis color pink is not like a hot or neon pink color but is like a pastel pink which is slightly softer in color but awesome looking
We use a professional grade of nylon webbing which can be used for many applications
Our webbing is a on the is what we called standard stiffness which is used mainly for harnesses and weight belts becuase it has some flexibility but also is slightly flexible. A great webbing to use
This webbing is just softer in flex than our med stiff red and other color webbing
Used for weight belts and other applications
Our webbing is made to be more durable for underwater use making it last longer and works better on weight belts, harnesses and backstraps and cam straps!
This webbing is design for marine use and will hold up very well with underwater use
So we found these awesome little rubberize underwater ties for many uses on your dive rig! From securing hoses to locking down small clips these little guys are reusable so you can keep using them for different jobs on your rig
They are covered in a rubberized material to keep them from rusting. Just twist and hold your item down
These are 3" inches long
They are super strong for holding items that could be heavy
They come in 2 bright colors High viz Yellow and Safety Orange plus our tec black
Just order one when your placing an order and you will come back for more!!!
So we found these awesome little rubberize underwater ties for many uses on your dive rig! From securing hoses to locking down small clips these little guys are reusable so you can keep using them for different jobs on your rig
They are covered in a rubberized material to keep them from rusting. Just twist and hold your item down
These are 3" inches long
They are super strong for holding items that could be heavy
They come in 2 bright colors High viz Yellow and Safety Orange plus our tec black
Just order one when your placing an order and you will come back for more!!!
So we found these awesome little rubberize underwater ties for many uses on your dive rig! From securing hoses to locking down small clips these little guys are reusable so you can keep using them for different jobs on your rig
They are covered in a rubberized material to keep them from rusting. Just twist and hold your item down
These are 6" inches long
They are super strong for holding items that could be heavy
They come in 2 bright colors High viz Yellow and Safety Orange plus our tec black
Just order one when your placing an order and you will come back for more!!!
So we found these awesome little rubberize underwater ties for many uses on your dive rig! From securing hoses to locking down small clips these little guys are reusable so you can keep using them for different jobs on your rig
They are covered in a rubberized material to keep them from rusting. Just twist and hold your item down
These are 6" inches long
They are super strong for holding items that could be heavy
They come in 2 bright colors High viz Yellow and Safety Orange plus our tec black
Just order one when your placing an order and you will come back for more!!!
So we found these awesome little rubberize underwater ties for many uses on your dive rig! From securing hoses to locking down small clips these little guys are reusable so you can keep using them for different jobs on your rig
They are covered in a rubberized material to keep them from rusting. Just twist and hold your item down
These are 6" inches long
They are super strong for holding items that could be heavy
They come in 2 bright colors High viz Yellow and Safety Orange plus our tec black
Just order one when your placing an order and you will come back for more!!!
Our Piranha Accessory Keeper is ideal for holding down backup lights but can also be used on the shoulder strap to retain your inflator hose
This keeper uses our larger 3/16" inch bungee for more support
Using 3/16 bungee now gives you an option for a better support on holding items in place during your dive
Now you have more choices when building or adding to your harness to make it custom for you!
Each side is slightly bent to allow your bungee to hold your items in place
Fits on 2" inch wide webbing
This keeper uses our special no damage teeth! Still giving you the grip you want without damaging your webbing
Included is a 9" inch piece of colored bungee for each keeper! Our 9" inch piece allows you to decide on do you need a small loop or a larger loop? Just adjust the length and knot off each side.. Select your color below
You are purchasing ONE (1) keeper!
Made out of marine grade stainless steel to reduce your item from rusting!
This product is also made in the good ole Usa for Piranha!
Our Piranha Accessory Keeper is ideal for holding down backup lights but can also be used on the shoulder strap to retain your inflator hose
Our keeper uses 1/8" inch bungee
This keeper uses our special no damage teeth! You still get a bite on your webbing without damaging your webbing!
Now you have more choices when building or adding to your harness to make it custom for you!
Each side is slightly bent to allow your bungee to hold your items in place
Fits on 2" inch wide webbing
Included is a 9" inch piece of colored bungee for each keeper! Our 9" inch piece allows you to decide on do you need a small loop or a larger loop? Just adjust the length and knot off each side.. Select your color below
You are purchasing ONE (1) keeper! but want 2? Add from our drop down box and save!!
Made out of marine grade stainless steel to reduce your item from rusting!
This product is also made in the good ole Usa for Piranha!
Our Piranha Accessory Keeper is ideal for holding down backup lights but can also be used on the shoulder strap to retain your inflator hose
This keeper uses our larger 3/16" inch bungee for more support
Using 3/16 bungee now gives you an option for a better support on holding items in place during your dive
Now you have more choices when building or adding to your harness to make it custom for you!
Each side is slightly bent to allow your bungee to hold your items in place
Fits on 2" inch wide webbing
Included is a 9" inch piece of colored bungee for each keeper! Our 9" inch piece allows you to decide on do you need a small loop or a larger loop? Just adjust the length and knot off each side.. Select your color below
You are purchasing ONE (1) keeper!
Made out of marine grade stainless steel to reduce your item from rusting!
This product is also made in the good ole Usa for Piranha!
Our Piranha Accessory Keeper is ideal for holding down backup lights but can also be used on the shoulder strap to retain your inflator hose
Our keeper uses 1/8" inch bungee
Now you have more choices when building or adding to your harness to make it custom for you!
Each side is slightly bent to allow your bungee to hold your items in place
Fits on 2" inch wide webbing
Included is a 9" inch piece of colored bungee for each keeper! Our 9" inch piece allows you to decide on do you need a small loop or a larger loop? Just adjust the length and knot off each side.. Select your color below
You are purchasing ONE (1) keeper!
Made out of marine grade stainless steel to reduce your item from rusting!
This product is also made in the good ole Usa for Piranha!
Another great little piece of hardware we made per a customer request!
This has a 3 divided slot area
We also have a hole for your 3/16" Bungee cord
These are made for either your shoulder straps or run them along your waist to quickly clip off
These are made out of 304 marine grade hardware so you know these are highly rust resistantance
And yes these are tumbled for 48 hours giving them a smooth edge with nothing sharp to cut your webbing
NOTE: If you select the hole to your leftside then understand that when looking at your rig the hole would be on the right. So looking at that hole your righthand would grab it. Hope we are giving you enough info. Look at the bungee hole in the picture on the wwebsite and that is a right side hole
This is a bent D-Ring on the lower part of the drop ring along with a Chest Strap loop or you could clip off on this outside slot
The D loop is roughly 1 3/8" Inches long. This is the inside measurement
We use a 304 marine grade stainless steel material for strength and durability
We tumble this hardware for 48 hours giving them smooth edges all around and nothing to cut your webbing!
Fits 2" inch webbing any thickness
Select from flat to slight bend and a 90 degree bend from our drop down list
You are purchasing 1 piece so if you want 2 please select 2
If you select 2 pieces and also you want them bent we will bend them to work as a complete left and right set! Unless you put in our comment section you wish something else
We always adding new items that divers request like this sidemount piece to help you with your sidemount rig
This piece will hold your 3/16" bungee in place with a slight notch we added so no slipping or bungee jumping out of place unless you want to remove it
We use a 304 marine grade stainless steel material for strength and durability
We tumble this hardware for 48 hours giving them smooth edges all around and nothing to cut your webbing!
Want to add a little more comfort down at your waist? Add our waist pads to do just that
Uses a 2" inch smooth slide to help hold in place during your dive with 2 sewn bands on each end. This allows you to slide your 2" inch webbing thru the sewn in bands with the slide make it lock in position once you align your waist pads
You get 2 comfort pads in your package
The short pad is roughly 9 3/4" / 24cm long where it is padded for comfort
The long one is 11 3/4" inches long covering more area
So we here at Piranha just added more to our slip-on hardware to make your life easier
You can now add this piece onto a harness without removing everything off to slide on your new piece!
This will work with our 2" webbing soft "standard" or our stiffer webbing not a problem
We also tumbled these for 48 hours to give them an ultra soft edge and that will not cut or damage your webbing
We also added a couple of holes so you can add bungee / Latex tubing if you wish too! 1/8" on the smaller holes or 3/16" on the larger holes!
Made from marine grade 304 stainless steel so you know it will not rust for a longer life!
Overall Width: 3" Inches
End Loop Length ID" 1" inch
Thickness: 1/8" inch
Select from our drop down box below if you want your hardware with either a slight bend on the loop or a 90 degree bend on the loop
If you want the loop part to be on the leftside select Left and if you want the loop on the right you would select rightside. The loop is built to be as you look down when wearing it.
We use a professional grade of nylon webbing which can be used for many applications and this webbing is our heavy duty soft webbing we were able to get!
This webbing is slightly softer than our standard version. If your looking for a soft / conforming webbing to you and your harness this could be your webbing..
NOTICE: We would not recommend this webbing for weight belt use since it is softer and may roll with that weight being applied on it! This webbing is more for harness use where you want it to conform and hug your body
our webbing is made to be more durable for outdoor weather environments making it last longer and works better on weight belts, harnesses and backstraps!
Another perfect piece of hardware to define your dive rig
Made out of marine grade 304 stainless steel to reduce rusting
This is our flat version for those who may want to further custom this hardware for there diving needs! We take the time to produce a high quality product you will be pround of using on your dive rig.
Our hardware is tumbled for 48 hours giving the edges a smooth touch and feel plus doing this reduces the chance of your webbing being cut or damaged from our hardware!
We use 1/8" thick stainless allowing it to be lightweight yet still having enough strength for long term durability
This will work with our any of our 2" webbing is not a problem
We also tumbled these for 48 hours to give them an ultra soft edge and will not cut or damage your webbing
Made from marine grade 304 stainless steel so you know it will not rust for a longer life!
Lastly we added holes for both 1/8" & 3/16" bungee or latex tubing if you want to secure a piece of dive gear plus you can add any of our 2" inch d-rings to go with this tri-glide and still be able to use your bungee or latex tubing
This backmount you use with 2" inch webbing. Our clip uses 3 connections points! One on each side plus we added a lower one to gice you more options!
This backmount clip with no teeth we placed a slight angle on the lower loops making this just a little easier to clip off to while your diving! Our lower plate we use a slight bend making it even easier to find when your reaching around! Plus we gave you two more side loops to clip too!
Overall width is roughly 4 1/4" inches wide at the widest point!
Length is roughly 4 1/4"
1/8" thick gives it still lightweight but strength
Made from 304 stainless steel
Great for hanging smb's, liftbags or other items
We have tumbled this item for 48 hours to have all the edges be smooth and prevents any webbing damage
Our trim pockets hold upto 5lbs pound of soft or hard weight
Velcro closure holds the secure while diving
Pocket has a grommet hole at the bottom for quick drainage
The backside has velcro tabs so it is easy to place on or off
We do recommend that you purchase weight belt keepers one for each side. These keepers keep your pocket from slidding around during your dive! If your using these on your tank strap then you do not need the keepers to hold the trim pocket in place
Made in a heavy conduro material so it will last longer during harsh use
With our latest storage pocket you can store it behind you using our 2 stainless steel grommets that are spaced 5 5/8" inces apart or we added on the backside where you can slide yourr 2" inch webbing through it to store it another way / place
Depending on how you use this pocket you can store surface markers or liiftbags? and you can secure the open end by using the velcro to close the pocket
Want to use a surface marker with a finger spool? No problem with the webbing slot on the back side you can use ths pocket that way in a vertical layout
You can even store your back-up mask if you choose or your light?
This pocket has has a drainage grommet to help remove water quickly when not in use
Llightweight denair material gives you strength and also allows your pocket to quiickly dry when not in use
You can also purchase lockig clips to hold your pocket in place so it is not sliding around or quick links if using to hang off your backend!
Dimensions are:
Length" 10" inches of inside usable space with a 4 3/4" inch diameter allowing you to use this pocket in many ways
So we just got in some cool 1" diameter silicone bands in colors!
Yup you heard it right we now have color bands with more colors comming in
So you can always choose our black 5 pack of rubber bands or now get these color bands to give your rig evena more one of a cool look while stram lining your rig by safetly securing your hoses from moving all over the place!
These are 1" inch in diameter by 9/16 wide
These will also stretch to hold your hoses or other rigging items in place during your dive
- Made out of a premium marine grade 316 stainless steel for diving use on backplates pads and other scuba uses. These are1 piece and male and female end you are purchasing. The flat bottom allows for a better fit when securing items on to your rig
- These Lightweight, strong, sturdy, high strength and corrosion resistant in saltwater circumstance
- Used to attach equipment accessories such as mesh bag with grommet on to the backplate
- Universal fits the standard holes on any standard backplate
- Great gear replacement accessories for underwater scuba diving,
So we built a d-ring to mount onto almost any backplate! How you ask? Well we made one of the holes fixed so your d-ring stays located in the same area and then we made a 2 1/4" long slot so no matter where you mount it and on any of the different made backplates you can secure the bottom hardware by sliding it to match up with another hole in your backplate!!
We also made this d-ring just a little larger then normal to make sure you can find it with ease on the side of your plate! Ir reaces out 1 5/8" inches measuring the inside of the D
We also supply all the needed 3/8"-16 stainless steel hardware and use a nylon insert lock nut to hold it tightly to your plate. Our kit includes:
1 Backplate D-Ring ** 304 marine grade stainless
2 7/32 Hex Head button cap screw **316SS
* You need a 7/32 Allen Head Tool for this bolt
2 Nylon insert lock nut **316SS
4 Washers **316SS
Overall Measurements:
3 1/2" inches long
2 5/8" inches wide
1/4" thick
1 5/8" inside D measurement
Slot Measurement: Middle of fixed hole to shortest to furtherest slot length: 15/16" to 3" inches
Your backplate D-Ring has been tumbed for at least 48 hours giving it a smooth finish with no sarpe edges
If you want your D-ring slightly bent select from our drop down box below and make sure to read to know how the bend will be facing
* Example: If you select the fixed hole on the top and you want your D-ring slightly bent forward it means your bend is slightly in front of your backplate hardware and if bent backwards it would mean your bend is slightly behind where you mount it...
So you need to carry different items and need a place to store them during your dive? We got it for you
This pocket has two front pockets with heavy duty zippers!
The zippers have pull tabs so even with gloves you can open with ease!
A third zipper allows you to open the pocket even wider if you need too and expands it open by over 3" inches wide!
The larger rear pocket is roughly 11" inches long X 7 1/2" tall and can be open to over 3" inches wide!
The smaller front pocket has 2 grometed drain holes and is roughly: 10 1/4" inches long X 6" inches tall
The back has 2 4" inch stainless steel double enders to connect your pocket to you or just use the 1" inch stainless steel d=rings and connect by your method.
You also have a velcro closure on the backside that holds your double enders when not in use or during a dive you can also store smaller items in there
The Material is made from a heavy duty: 1000D nylon with PU coating giving you one tough pocket that will last you during even your harsh dives
So we have done it again bringing you another product that allows you more storage
* Material: Wear-resistant 1680D PU-coated nylon which gives it a tough outer shell
* Comes with elastic thigh straps with quick release buckles
Adjustable straps around the thigh with quick release fasteners.
* We use a #10 rust-proof YKK zipper on the main compartment which is large enough to grab with even gloves on. The main compartment you can place finger spools, SMB's or other items needed for your dive
* Dimension: 25cm × 15cm × 6cm (9.8" x 5.9" x 2.4")
* Our pocket has two separate compartments, one on the front side uses a Velcro closure to secure your item! Great place for slates and the main compartment comes with a YKK zipper to hold your goodies
* We also have a drainage gromet on the bottom of the main compartment to remove water quickly from your pocket
* Lastly we use an adjustable loop on the back side to slip on your waist and the triglide also allows you to make the loop smaller or larger depending on the webbing you are using
So our latest product is a slightly altered tri-glide that used to be made but we made some changes to it!
The issue with the older one it was just a slight bit to long depending on your mounting location so we shorten it slightly allowing you to mount it without causing any interference..
We make this product in the Usa! and it is made out of a marine grade 304 stainless steel
We have these tumbled for 48 hours allowing you to get a smooth edge product and nothing to cut your webbing with sharpe edges
Overall length:3 1/2" inches
Webbing slot is 2" inches wide / smooth no teeth design... Works with any 2" inch scuba webbing
Overall Width: 1 3/8" inches at the widest point
2 Clips points on either side or purchase two and a chest strap and you have a daul funtion piece
So our newest pocket has the following features which really makes this pocket one hot deal
We built this baby to last so we used a very durable 1680D nylon with PU coating!
Everything built with this pocket screams quality from the stitch work to the material we used so enjoy!
1 large rear pocket to hold many different goodies plus has 2 1" inch stainless steel d-rings to secure items you may want to leash
Also has a mesh rear pocket inside to hold flat objects or smaller items you may run across on your dive!
This rear pocket is roughly 10" inches long by 5" inches wide / deep! But wait you will notice that we have a zipper around the outside and if you unzip this zipper it will expand your pocket by roughly 2+ inches!
Our front smaller pocket has has 1 one inch stainless steel d-ring to leash items too also roughly 10 inches long by 4 inches deep!
We also include 2 4" inch stainless steel double enders which you can fix onto the outside 1 inch stainless steel d-rings if you want or we also added almost a 7 inch long by 2 inches wide webbing slot if you want to slide on your dive rig
All in our special color of Tec BLACK!
We use these as belly / front storage pockets but with all our added features go ahead and make it work for your dive!
So with this pocket you can use it on your harness! sidemount or almost anywhere you want to secure your dive weights
Our lastest pocket will hold upto 5lbs soft or hard weights!
No more worrying about the pocket sliding with the added stainless steel smooth tri-glides on each side. So slide your webbing through the tri-glides and secure the pocket in to position it really is that easy
Use a large velcro flap to hold your weight in place during the dive
We also use a hard piece on the inside on the back of the pocket so it will not bend or flex during use
Rigging for use with your aluminum 80 or low preesure 85 cylinders. We found that if your cylinder has a 7" inch to 7 1/4" diameter you can use this holding system to clip off too
Uses 1 1/2" webbing and a stainless steel buckle
Large stainless steel snap with an adjustable slider to get your rigging just right for your dive
Piranha has come up with a another travel backplate with an easy carry handle!
This plate comes with multiple slots so you can vary your adjustments on your harness
Dual rail slots on the back to hold your your cylinder
Rear rail slots on the back align the cylinder and make this plate very stiff!
Made for diving with a single cylinder but can be used with doubles also! Has the hardware holes for doubles use!!
This tough and very durable backplate will last years od service and your back will thank you for lightening the load
This backplate comes with harness and be ready to go! You just need to add a tank cam strap to slip on and ready to go!
***Our standard harness included with this plastic heavy duty backplate includes item below!
** Soft black 2" inch wide webbing for a comfort fit
** Stainless steel buckle and 3 6mm straight D-rings with slides
** Stainless steel buckle!
** The harness is already been built so no guess work just add a tank cam strap. If you have one then just order this kit if not go check out our different type to see which one best fits your needs
* Made out of 304 marine grade stainless steel so you know these will be durable
* Our latest end loops now have webbing teeth to help reduce any movement on your webbing! Just enough bite but with non damaging teeth to your webbing.
* You can flip this so the end loop is either on your left or right!
* Now you can select your bend! from our drop down box!!
This has an end loop to clip off easy and we added a dropped D-Ring for even more gear configurations!
* We tumble these for 48 hours giving us smooth edges! Nothing sharp to cut or damage your webbing
* These fit up to a 2" inch wide webbing!
* This product is produced in the U.S.A!
* You are purchasing 1 piece!
** You can select with left or right side loop from our drop down boxes!
* Dimensions:
- Overall Length includes the drop D: 2 1/2" inch long
* Our newest dual end loops with a dropped D-Ring are cut with a waterjet
* Made out of 304 marine grade stainless steel so you know these will be durable
* Our latest dual end loops now have webbing teeth to help reduce any movement on your webbing! Just enough bite but with non damaging teeth to your webbing.
* Our dual ended loop model noe allows you to have several clip off options during your dive!
This has a dual end loop to clip off easy and we added a dropped D-Ring for even more gear configurations!
* We tumble these for 48 hours giving us smooth edges! Nothing sharp to cut or damage your webbing
* These fit up to a 2" inch wide webbing!
* This product is produced in the U.S.A!
* You are purchasing 1 piece!
** Select which bend you want from a flat to a slight or 90 degree bend!
* Dimensions:
- Overall Length includes the drop D: 2 3/8" inch long
We use a professional grade of nylon webbing which can be used for many applications
This medium stiff webbing is just has a little more stiffness then our standard black webbing which is soft and flexible. This one is right between our standard bersion and our stiffest version. We love this one for harnesses
Our webbing is a little stiffer than most webbing and made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses and backstraps!
Our 1 1/2" Inch crotch strap works with our backplates and many others on the market today!
Our 1 1/2" inch crotch strap runs from the adjustable part of the strap on the rear to mount to the slot in the backplate to the front where the loop goes on the waist belt webbing at the front of your harness
Using this crotch strap helps to maintain your harness from moving up on our body during a water entry from a boat or while ascending during your dive. Also by holding your rig in place this prevents your cylinders/valves from contacting your head
Our strap has a 1 1/2" inch BLACK stainless steel scooter ring for use with diver propulsion vehicles at the front of the strap right below the webbing loop.
You can also use this 1 1/2" inch BLACK scooter ring for applications such as a temporarily place to clip off an item such as reels, spools or camera's.
We use a 1 1/2" inch soft black webbing so it does not cut into your wetsuit material or cause any damage that stiffer webbing can cause
The 1 1/2"-inch continuous webbing crotch strap is preferred by tec divers who use Scooter's or DPVs for extended dive periods. The 1 1/2 inch webbing creates a distribution of weight because of the width provides a greater secure feeling during those dives
This strap uses a 2 piece plastic snap to quickly release yourself from your rig
Also uses 2 heavy duty plastic slides to adjust for that perfect fit!
At Piranha we keep offering you more choices when you want to build your rig or just want to stand out from a crowd! We now are offering one of our newest colors in our soft Nitrox Green Webbing..
We use a professional grade of nylon webbing which can be used for many applications
Our Nitrox Green webbing is a is a standard stiffness and our webbing is made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses, Crotch Straps and backstraps!
At Piranha we keep offering you more choices when you want to build your rig or just want to stand out from a crowd! We now are offering one of our newest color in our soft Webbing..High Vis Yellow
We use a professional grade of nylon webbing which can be used for many applications
Our High Vis Yellow webbing is a is a standard stiffness and our webbing is made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses, Crotch Straps and backstraps!
* Made out of stainless steel so you know these will be durable
* Our latest end loops now have webbing teeth to help reduce any movement on your webbing! Just enough bite but with non damaging teeth to your webbing.
* We tumble these for 48 hours giving us smooth edges! Nothing sharp to cut or damage your webbing
* These fit up to a 2" inch wide webbing!
* You now can choose from a flat, angled or 90 degree bent from our drop down box!
So our newest piece of hardware just came in and if your looking for hanging items behind you well check out this piece!
Made of our stainless steel so you know salt or fresh water will not hurt it
1/8" Thick makes it durable
This is a straight mounting bracket with 2 large clip off loops on each side to better clear your back-side and makes it simply to find when reaching around
We made this with 4 slots so you can use 2 or 4 depending on what your diving and your needs
We have these tumbled for 48 hours giving them a smooth finish so as not to hurt your webbing thru the slot area
Overall length is roughly 6 3/4" inches
Loop Area is 1 7/8" long opening by 2 3/16" inches wide:: Inside measurement
Select flat or bent type from our drop down box below
Check out Hog's tri-glide n the standard finish and check out some awesome features
This is a brushed satin stainless steel material in a Black finish
You can clip off on either side of this glide or use it on your waist strap and face the D position downwards for an easy gauge clip off
The slots are wide enough to be able to slide 2 pieces of webbing through it or a simple slide into the right position then take a look this special tri-glide
Check out Hog's tri-glide n the standard finish and check out some awesome features
This is a brushed satin stainless steel material
You can clip off on either side of this glide or use it on your waist strap and face the D position downwards for an easy gauge clip off
The slots are wide enough to be able to slide 2 pieces of webbing through it or a simple slide into the right position then take a look this special tri-glide
So we finally have them in! Our Stealth black powder coated hardware is tough and very durable. These are the same bent d-ring with stainless steel under our tough black powder coating! Welcome to our stealth series of hardware
2" D'Ring made from high quality Stainless Steel with black powder coating over the top of it
Our newest 6mm BENT D-Rings! We bend them right here in the good ole USA!
6.0mm Extra heavy duty diameter ring
Add to your harness or rig for more attachment points
Use either smooth or teeth slides to help lock in position
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistance materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
The four outer holes fit a 3/16 bungee or latex tubing if you want
Overall Length: 3 3/16" inches
Width: 1 3/16" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistance materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
The four outer holes fit a 3/16 bungee or latex tubing if you want
Overall Length: 3 3/16" inches
Width: 1 3/16" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We use an electroplated process to make our assembly screws
This allows our assembly screws to very durable and take the harsh conditions of our diving environments
Any accessory using grommets, you can use these screws to mount that item to your rig! Items backplate pads, liftbag pouches, buttplates and other items
We use o'rings on the inside of each end, This allows the screws to hold in place and not need a lock washer!
So we here at Piranha just added more to our slip-on hardware to make your life easier
You can now add this piece onto a harness without removing everything off to slide on your new piece!
This will work with our 2" webbing soft "standard" or our stiffer webbing not a problem
We also tumbled these for 48 hours to give them an ultra soft edge and that will not cut or damage your webbing
We also added a couple of holes so you can add bungee / Latex tubing if you wish too! 1/8" on the smaller holes or 3/16" on the larger holes!
Made from marine grade 304 stainless steel so you know it will not rust for a longer life!
Overall Width: 3" Inches
End Loop Length ID" 1" inch
Thickness: 1/8" inch
Select from our drop down box below if you want your hardware with either a slight bend on the loop or a 90 degree bend on the loop
If you want the loop part to be on the leftside select Left and if you want the loop on the right you would select rightside. The loop is built to be as you look down when wearing it.
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistance materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
The four outer holes fit a 3/16 bungee or latex tubing if you want
Overall Length: 3 3/16" inches
Width: 1 3/16" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistance materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
The four outer holes fit a 3/16 bungee or latex tubing if you want
Overall Length: 3 3/16" inches
Width: 1 3/16" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistance materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
The four outer holes fit a 3/16 bungee or latex tubing if you want
Overall Length: 3 3/16" inches
Width: 1 3/16" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistance materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
The four outer holes fit a 3/16 bungee or latex tubing if you want
Overall Length: 3 3/16" inches
Width: 1 3/16" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
Our sliders are made for us and are made to our specs which allows us to make these a heavy duty style! These will not bend or twist like the thinner ones most retailers sell!
Plastic Slide smooth
Made from high quality stainless material
1 1/2" width for 1 1/2" ide webbing!!
Great for locking items on your harness
These will allow you to adjust your gear a little easier than the tooth version
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistance materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
The four outer holes fit a 3/16 bungee or latex tubing if you want
Overall Length: 3 3/16" inches
Width: 1 3/16" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
This new D-Ring we now have added a 3rd option for clipping to/from! We added a low profile D-ring at the bottom to allow for even more flexibility to your rig!!
You can use this has a triple under the counterlung d-ring or slide it on your 2 inch crotch strap towards the rear and now you have a place to attach spools, reels or even Smb / liftbags and even more with the 3rd low profile rear D-ring!!!
Fits 2 inch webbing... measures loop 2 inch "ID" w/ 1.5 inch long "ID"
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistance materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
The four outer holes fit a 3/16 bungee or latex tubing if you want
Overall Length: 3 3/16" inches
Width: 1 3/16" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistance materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
Expose this to your dive light or sun light and it will glow in the dark! On a boat for a night dive? Your dive harness you be easy to spot with these on
The four outer holes fit a 3/16 bungee or latex tubing
Overall Length: 3 3/16" inches
Width: 1 3/16" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistaned materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
You can also use these with any of our D-rings and if you use our slotted d-rings " Stainless or Aluminum" well you do not need to take your harness apart just slip on
Also if you look on one side we add webbing bumps this will reduce your webbing from sliding! Make sure the bumps are facing upwards for best results
This clip can do about anything you need on your dive harness. Just add some color so you know your dive harness from anybody else!
We also made our famous webbing slip on open slots so you do not need to remove or tear your harness down just slip it on and your ready to go. Works with our soft to stiff webbing not an issue
With our 3/16" bungee you can mount 1, 2, 3 or up to a 4lb hard weight When you secure your hard weight we also recommend you make your your knot on the backside is tight so the bungee will not move
The four outer holes fit a 3/16 bungee plus we include 4 feet of our marine grade bungee cord! We have this cord made for us to a high standard for strength and durability and this is also UV resistane
Overall Length: 2 7/8" inches
Width: 1 3/4" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistaned materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
You can also use these with any of our D-rings and if you use our slotted d-rings " Stainless or Aluminum" well you do not need to take your harness apart just slip on
Also if you look on one side we add webbing bumps this will reduce your webbing from sliding! Make sure the bumps are facing upwards for best results
This clip can do about anything you need on your dive harness. Just add some color so you know your dive harness from anybody else!
We also made our famous webbing slip on open slots so you do not need to remove or tear your harness down just slip it on and your ready to go. Works with our soft to stiff webbing not an issue
With our 3/16" bungee you can mount 1, 2, 3 or up to a 4lb hard weight When you secure your hard weight we also recommend you make your your knot on the backside is tight so the bungee will not move
The four outer holes fit a 3/16 bungee plus we include 4 feet of our marine grade bungee cord! We have this cord made for us to a high standard for strength and durability and this is also UV resistane
Overall Length: 2 7/8" inches
Width: 1 3/4" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistaned materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
You can also use these with any of our D-rings and if you use our slotted d-rings " Stainless or Aluminum" well you do not need to take your harness apart just slip on
Also if you look on one side we add webbing bumps this will reduce your webbing from sliding! Make sure the bumps are facing upwards for best results
This clip can do about anything you need on your dive harness. Just add some color so you know your dive harness from anybody else!
We also made our famous webbing slip on open slots so you do not need to remove or tear your harness down just slip it on and your ready to go. Works with our soft to stiff webbing not an issue
With our 3/16" bungee you can mount 1, 2, 3 or up to a 4lb hard weight When you secure your hard weight we also recommend you make your your knot on the backside is tight so the bungee will not move
The four outer holes fit a 3/16 bungee plus we include 4 feet of our marine grade bungee cord! We have this cord made for us to a high standard for strength and durability and this is also UV resistane
Overall Length: 2 7/8" inches
Width: 1 3/4" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We use a professional grade of nylon webbing which can be used for many applications
Our blue webbing is a is a standard stiffness and our webbing is made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses and backstraps!
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistaned materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
You can also use these with any of our D-rings and if you use our slotted d-rings " Stainless or Aluminum" well you do not need to take your harness apart just slip on
Also if you look on one side we add webbing bumps this will reduce your webbing from sliding! Make sure the bumps are facing upwards for best results
This clip can do about anything you need on your dive harness. Just add some color so you know your dive harness from anybody else!
We also made our famous webbing slip on open slots so you do not need to remove or tear your harness down just slip it on and your ready to go. Works with our soft to stiff webbing not an issue
With our 3/16" bungee you can mount 1, 2, 3 or up to a 4lb hard weight When you secure your hard weight we also recommend you make your your knot on the backside is tight so the bungee will not move
The four outer holes fit a 3/16 bungee plus we include 4 feet of our marine grade bungee cord! We have this cord made for us to a high standard for strength and durability and this is also UV resistane
Overall Length: 2 7/8" inches
Width: 1 3/4" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistaned materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
You can also use these with any of our D-rings and if you use our slotted d-rings " Stainless or Aluminum" well you do not need to take your harness apart just slip on
Also if you look on one side we add webbing bumps this will reduce your webbing from sliding! Make sure the bumps are facing upwards for best results
This clip can do about anything you need on your dive harness. Just add some color so you know your dive harness from anybody else!
We also made our famous webbing slip on open slots so you do not need to remove or tear your harness down just slip it on and your ready to go. Works with our soft to stiff webbing not an issue
With our 3/16" bungee you can mount 1, 2, 3 or up to a 4lb hard weight When you secure your hard weight we also recommend you make your your knot on the backside is tight so the bungee will not move
The four outer holes fit a 3/16 bungee plus we include 4 feet of our marine grade bungee cord! We have this cord made for us to a high standard for strength and durability and this is also UV resistane
Overall Length: 2 7/8" inches
Width: 1 3/4" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistaned materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
You can also use these with any of our D-rings and if you use our slotted d-rings " Stainless or Aluminum" well you do not need to take your harness apart just slip on
Also if you look on one side we add webbing bumps this will reduce your webbing from sliding! Make sure the bumps are facing upwards for best results
This clip can do about anything you need on your dive harness. Just add some color so you know your dive harness from anybody else!
We also made our famous webbing slip on open slots so you do not need to remove or tear your harness down just slip it on and your ready to go. Works with our soft to stiff webbing not an issue
With our 3/16" bungee you can mount 1, 2, 3 or up to a 4lb hard weight When you secure your hard weight we also recommend you make your your knot on the backside is tight so the bungee will not move
The four outer holes fit a 3/16 bungee plus we include 4 feet of our marine grade bungee cord! We have this cord made for us to a high standard for strength and durability and this is also UV resistane
Overall Length: 2 7/8" inches
Width: 1 3/4" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistaned materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
You can also use these with any of our D-rings and if you use our slotted d-rings " Stainless or Aluminum" well you do not need to take your harness apart just slip on
Also if you look on one side we add webbing bumps this will reduce your webbing from sliding! Make sure the bumps are facing upwards for best results
This clip can do about anything you need on your dive harness. Just add some color so you know your dive harness from anybody else!
We also made our famous webbing slip on open slots so you do not need to remove or tear your harness down just slip it on and your ready to go. Works with our soft to stiff webbing not an issue
With our 3/16" bungee you can mount 1, 2, 3 or up to a 4lb hard weight When you secure your hard weight we also recommend you make your your knot on the backside is tight so the bungee will not move
The four outer holes fit a 3/16 bungee plus we include 4 feet of our marine grade bungee cord! We have this cord made for us to a high standard for strength and durability and this is also UV resistane
Overall Length: 2 7/8" inches
Width: 1 3/4" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
Our reinforced delrin cam buckle is a perfect replacement and now is in colors to get you more of a custom look!!
You can adjust the strap by the stainless steel slider by the buckle
Length of strap is approximately 35 inches long
Velcro to secure your cylinder on your back
NEW! We now have color buckles in Blue, Red and Yellow! Add more color to your rig and never get confused who's rig it is on the dive boat!!
You get the color buckle that you choose! plus a 2" inch wide tank strap that you can adjust with the stainless steel slider you are supplied with also!!
Does NOT come with a removable anti-slip pad! Since many cam straps have them we did not add this and keeping your costs lower!! You can order the slip pads from our drop down box below if you need them!
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistaned materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
You can also use these with any of our D-rings and if you use our slotted d-rings " Stainless or Aluminum" well you do not need to take your harness apart just slip on
Also if you look on one side we add webbing bumps this will reduce your webbing from sliding! Make sure the bumps are facing upwards for best results
This clip can do about anything you need on your dive harness. Just add some color so you know your dive harness from anybody else!
We also made our famous webbing slip on open slots so you do not need to remove or tear your harness down just slip it on and your ready to go. Works with our soft to stiff webbing not an issue
With our 3/16" bungee you can mount 1, 2, 3 or up to a 4lb hard weight When you secure your hard weight we also recommend you make your your knot on the backside is tight so the bungee will not move
The four outer holes fit a 3/16 bungee plus we include 4 feet of our marine grade bungee cord! We have this cord made for us to a high standard for strength and durability and this is also UV resistane
Overall Length: 2 7/8" inches
Width: 1 3/4" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
NOTE: These are the larger diameter rings for rescue / commercial use!
Add to your harness or rig for more attachment points
Use either smooth or teeth slides to help lock in position
304 Grade Stainless Steel
This is for folks that are using for extreme diving conditions! These are the heavest D-Rings available on the market today at a Piranha Dive Price!!
Normal d-rings are 5mm light duty, 6mm standard heavy duty and the 8mm are mostly used for commercial use and are really large so please keep this in mind. The 5mm and 6mm is used in rec and tech most common
We are adding more colors to dress your rig so it is yours and stands out from the crownd! We made our universal tri-glide / Weight plate in a wide range of colors to choose from so we have you covered
So we use UV resistaned materials so no fading from the sun
Talk about strong we put these through all types of tests plus diving applications to make sure your getting a quality product that will last you for years to come
You can also use these with any of our D-rings and if you use our slotted d-rings " Stainless or Aluminum" well you do not need to take your harness apart just slip on
Also if you look on one side we add webbing bumps this will reduce your webbing from sliding! Make sure the bumps are facing upwards for best results
This clip can do about anything you need on your dive harness. Just add some color so you know your dive harness from anybody else!
We also made our famous webbing slip on open slots so you do not need to remove or tear your harness down just slip it on and your ready to go. Works with our soft to stiff webbing not an issue
With our 3/16" bungee you can mount 1, 2, 3 or up to a 4lb hard weight When you secure your hard weight we also recommend you make your your knot on the backside is tight so the bungee will not move
The four outer holes fit a 3/16 bungee plus we include 4 feet of our marine grade bungee cord! We have this cord made for us to a high standard for strength and durability and this is also UV resistane
Overall Length: 2 7/8" inches
Width: 1 3/4" inches
Thickness: 3/16" inch
Fits any 2" inch wide webbing
We have tested our bracket to make sure that it will hold up during the roughest diving conditions some of us face
You also can select from our colors listed below and receive 3 feet to work your magic
NOTE: The webbing is a dark navy blue just a little darker then our picture is showing! Be aware!!
We use a professional grade of nylon webbing which can be used for many applications
Our webbing is a little stiffer than most webbings and made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses and backstraps!
We use a professional grade of nylon webbing which can be used for many applications
This webbing is a little stiffer than our medium Stiff black webbing and this is for divers looking for just a little more stiffness! This is our stiffest
Our webbing is a little stiffer than most webbing and made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses and backstraps!
We use a professional grade of nylon webbing which can be used for many applications
Our webbing is a little stiffer than most webbing and made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses and backstraps!
We use a professional grade of nylon webbing which can be used for many applications
Our webbing is a little stiffer than most webbings and made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses and backstraps!
We use a professional grade of nylon webbing which can be used for many applications
Our webbing is a little stiffer than most webbings and made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses and backstraps!
We use a professional grade of nylon webbing which can be used for many applications
Our blue webbing is a is a slightly stiffer webbing and our webbing is made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses and backstraps!
Specs
Rated Tensile Strength 4,575 ?- 5% Lbs.
Weight (oz/yd): 2.3 ?- .05
Width: 1 15/16 ? 1/32
Thickness .075?.005
Picks: 31 ?- 1
Marine grade quality "heavy duty"
You are purchasing BLUE webbing which is slightly darker then our blue standard webbing!
We use a professional grade of nylon webbing which can be used for many applications
Our webbing is a little stiffer than most webbing and made to be more durable to outdoor weather environment making it last longer and works better on weight belts, harnesses and backstraps!
So we finally have them in! Our Stealth black powder coated hardware is tough and very durable. These are the same bent d-ring with stainless steel under our tough black powder coating! Welcome to our stealth series of hardware
We bend our own D-rings in-house to make sure you get a quality bent D-ring!
Wire size is 5MM
Fits all 2 inch webbing
Made from high quality stainless steel with black powder coating over the stainless steel
A must have item for divers looking to find or attach an item where you cannot see and must use feel!
So we finally have them in! Our Stealth black powder coated hardware is tough and very durable. These are the same bent d-ring with stainless steel under our tough black powder coating! Welcome to our stealth series of hardware
2" D'Ring made from high quality Stainless Steel with black powder coating over the top of it
6.0mm Extra heavy duty diameter ring
Add to your harness or rig for more attachment points
Use either smooth or teeth slides to help lock in position
So we finally have them in! Our Stealth black powder coated hardware is tough and very durable. These are the same bent d-ring with stainless steel under our tough black powder coating! Welcome to our stealth series of hardware
Our sliders are made for us and are made to our specs which allows us to make these a heavy duty style! These will not bend or twist like the thinner ones most retailers sell!
Stainless Steel Slide w/ no teeth and black powder coating over them
Made from high quality stainless material underneath
2" width
Great for locking items on your harness
304 Grade Stainless Steel under the tough black powder coating!
So we finally have them in! Our Stealth black powder coated hardware is tough and very durable. These are the same bent d-ring with stainless steel under our tough black powder coating! Welcome to our stealth series of hardware
Our sliders are made for us and are made to our specs which allows us to make these a heavy duty style! These will not bend or twist like the thinner ones most retailers sell!
Stainless Steel Slide w/teeth and black powder coating over them
Made from high quality stainless material underneath
2" width
Great for locking items on your harness
304 Grade Stainless Steel under the tough black powder coating!
So we finally have them in! Our Stealth black powder coated hardware is tough and very durable. These have the stainless steel you love from us with our hard black powder coating!
2" D'Ring made from high quality Stainless Steel Black Power coated
5.0mm heavy duty diameter ring
Add to your harness or rig for more attachment points
Use either smooth or teeth slides to help lock in position
You are getting 2 pieces of bungee and 2 of our plastic hose retainers
This is our little hose retainer set-up for many uses
Use this to attach a clip or secure a piece of dive gear
Our retainer kit comes with 2 pieces of 6+" inches of bungee "select color"... and the the clip
Select the color of the Bungee from for the drop down below "Color will be the same for both retainers" When you purchase our 2 kit price you are saving $$$$
You can use this has a double under the counterlung d-ring or slide it on your 2 inch crotch strap towards the rear and now you have a place to attach spools, reels or even Smb / liftbags!
Fits 2 inch webbing... measures loop 2 inch "ID" w/ 1.5 inch long "ID"
Our sliders are made for us and are made to our specs which allows us to make these a heavy duty style! These will not bend or twist like the thinner ones most retailers sell!
Stainless Steel Slide w/teeth
Made from high quality stainless material
2" width
This slider has the raised center bar divers like to have! Allows you to move thicker webbing easy slot the slots
Our sliders are made for us and are made to our specs which allows us to make these a heavy duty style! These will not bend or twist like the thinner ones most retailers sell!
Stainless Steel Slide smooth
Made from high quality stainless material
2" width
Great for locking items on your harness
This slider has the raised center bar divers like to have!
These will allow you to adjust your gear a little easier than the tooth version
Our reinforced delrin cam buckle is a perfect replacement
You can adjust the strap by the stainless steel slider by the buckle
Length of strap is approximately 35 inches long
Velcro to secure your cylinder on your back
Does NOT come with a removable anti-slip pad! Since many cam straps have them we did not add this and keeping your costs lower!! You can order the slip pads from our drop down box below if you need them!
We build these using a 2" inch slider which allows you to adjust your final overall length..
Use for securing your cylinder
Strap length is 35 1/5" long by 2" wide roughly!
Has velcro to hold strap in place
Adds roughly 1 pound per camband. You can remove lead-weight off your belt!
Our cam straps are adjustable! We use a 2 inch SS slider which allows you to fit a large cylinder to a small pony bottle with the same strap!
You are purchasing one (1) camband. If you require two (2) please adjust your qty.
Does NOT come with a removable anti-slip pad! Since many cam straps have them we did not add this and keeping your costs lower!! You can order the slip pads from our drop down box below if you need them!
This is a wider no teeth slider more than a standard one and we have improved this slider with slightly thicker material making it more durable and stable
We also use a higher grade of stainless steel improving it from rusting in salt water use!
This is our heavy duty version which allows you to use thicker webbing or looping two pieces of webbing through will not be an issue with this webbing
Your standard slide has an opening of roughly 1/4 inch and this slide has a 3/8 opening making it a perfect slide for when you need to run two "2" pieces of webbing thru a slot.. No more fighting to get your webbing thru with this slide it now is simple and holds your webbing securely in place
Overall dimensions: 1 1/4 inch wide x 2 5/16 long with a slot opening of 3/8
This is the Newly design backpad back in stock! They now placed a pocket in the back of the pad for storing an Smb!
Our HOG backplate is made to fit most backplates sold in today's market!
Great for adding just a little more comfort when using doubles or rebreathers
You will need mounting screws to hold this pad onto your plate!
Piranha's Price: $39.95
Harness Accessories and Rigging Hardware
The rigging that turns a plate and webbing into your harness. Browse Piranha Dive long drop D-ring loops with webbing slots or chest strap slots, 2 inch straight and bent 6mm D-rings, single end loops with long drop rectangle D-rings, heavy duty 2 inch no-teeth tri-glide sliders, DSS single piece Hogarthian harnesses and Technical II aluminum backplates.
